Boiler service Bristol, all gas boilers serviced, exact appointment’s given, Call today on 07900 570 888 to book

We offer two levels of servicing…

What do we include in a Full Scope Boiler Service?

  • Visual inspection
  • Cleaning boilers condense trap
  • Cleaning of the magnetic filters on the system
  • Checking door / case seals
  • Removal of the combustion door / burner flange / compact thermal module
  • Checking thermal insulating mats
  • Cleaning the main heat exchanger with white vinegar (Vaillant) or Water Jets (Worcester) & non aggressive plastic brushes
  • Flushing through of the condense sump, trap and lines
  • Cleaning of the pre mix burner, spark electrodes, and flame rectification
  • Replacing the graphite burner flange seal
  • Replacing spark electrode gasket
  • Replacing combustion self locking nuts
  • Re greasing heat exchanger thread connections with copper grease.
  • Isolation of boiler and draining down
  • Checking expansion vessel pre charge
  • Refilling and purging the boiler
  • Checking correct boiler system water pressure
  • Checking min and max co/co2 with a flue gas analyser
  • Adjusting gas valve if required
  • Carrying out 26.9 checks
  • Checking boiler is gas tight
  • Heating system water health check using a turbidity tube
  • Fernox inhibitor / PH test using drip test

What do we include in a Limited Scope Boiler Service?

  • Visual inspection
  • Checking correct boiler system water pressure
  • Cleaning boilers condense trap
  • Cleaning magnetic filters on the system
  • Checking door / case seals
  • Checking min and max co/co2 with a flue gas analyser
  • Adjusting gas valve if required
  • Carrying out 26.9 checks
  • Checking boiler is gas tight
  • Heating system water health check using a turbidity tube
  • Fernox inhibitor test / PH test using drip test

‘Limited scope servicing is generally best for boilers under 5 years old’

“The above process follows the (very popular) ‘Vaillant ecoTEC’range of condensing boilers.
There may be slight process deviations and service parts within manufacturers, models and age, however the general process / principle remains the same…”

Not just a boiler service!

We test your system water for the presence of inhibitor and for turbidity levels on both service options. If there is diluted, reduced, or no inhibitor detected we will offer to treat the system by introducing a Fernox F1 chemical.

 

 

 

If during the heating water health check we find the turbidity levels high we will offer a solution to this also. It may include a system drain down to replace the current water, the installation of a magnetic filter, or a magnacleanse treatment.

They say a picture is worth a thousand words…

How long will the service take?

Our ‘full scope boiler service’ can take up to 2 hours. We may need to order service parts that are not carried on our van. Don’t worry though; we have a very good supplier that will deliver service parts when we need them.

Our ‘limited scope boiler service’ can take up to 40mins.

Will the service uphold the manufacturer’s warranty?

As a ‘gas safe’ registered company, our service packages will keep any major boiler manufacturers warranties and extended guarantees up to date, so relax, we got you covered.

Will the water and gas be switched off?

Absolutely not. We would never willingly prevent cups of tea being made!! We will isolate the gas and water supply at the boiler only, allowing cookers, toilets, and taps to be used. Unfortunately the hot water and the heating will be interrupted during the service.

Free boiler sticker with every service!

We will leave our contact details sticker on the boiler, showing the date serviced and the next recommended service date. If you have the original service book to hand then great, we can fill this in also.

If required, how much are the service parts?


Typical Vaillant ecoTEC plus,  ecoTEC pro, ecoTEC exclusive, ecoMAX service parts…

 

The graphite seal / burner flange seal is replaced once the compact thermal unit is removed. It cannot be reused so must be replaced…

Average cost £25

 

The ignition / monitoring electrode gasket is replaced once the ignition / monitoring electrode is removed. It cannot be reused so must be replaced…

Average cost £6

 

The ignition / monitoring electrode can normally be cleaned. Rarely replaced, but if we do…

Average cost £25

 

 

The heat proof insulation is replaced only if we find signs of damage. Rarely replaced, but if we do…

Average cost £30

 

 

The pressure sensor is replaced if blocked or multiple F75 faults are noted. Sometimes replaced, but if we do…

Average cost £25

 

Typical Worcester greenstar i, grennstar SI, greenstar CDI compact, greenstar CDI classic

 

The gaskets are replaced once access is gained to the burner. They cannot be reused so must be replaced…

Average cost £25 

 

 

 

The electrodes and flame rectification/ monitoring electrode can be cleaned on most boilers under a certain age. The flame rectification can wear easily though, and the old type with a glass viewing window will most likely be replaced…

Average cost £49

 

The bearing plate can sometimes split. Rarely replaced, but if we do…

Average cost £20

Find your boilers literature here:

Comments are closed.